ECE R80 PDF

ECE R80 describes two alternative test procedures to validate occupant safety of bus seats. Static loads are applied or the seats have to fulfill dynamic. ECE R80 – 关于客车座椅以及客车针对座椅结构的UNECE法规,此为法规的原始 版本以及对该版本的一些列修订和勘误。 对本法规的第2次修订已经. R Strength of seats and their anchorages for M2 and/or M3 http://www.

Author: Daijin Maule
Country: Costa Rica
Language: English (Spanish)
Genre: Science
Published (Last): 24 April 2007
Pages: 64
PDF File Size: 15.7 Mb
ePub File Size: 6.5 Mb
ISBN: 333-1-70780-373-8
Downloads: 26930
Price: Free* [*Free Regsitration Required]
Uploader: Fauzuru

Instrumentation” and published in The seat to be tested shall be complete with all upholstery and accessories. Where other modes of seat adjustment exist vertical, angular, seat-back, etc.

The competent authority which has granted type approval may at any time verify the conformity control methods applicable to each production unit and carry out on samples any test deemed necessary among the tests carried out for the approval.

ECE R80 Certified plastic bus seat city bus seat plastic seat for bus. The maximum displacement of the central point of application of each of the forces prescribed in paragraph 3.

The application for approval of the vehicle shall be submitted by the vehicle manufacturer or by his duly accredited representative. Then carefully return the back pan to the seat-back. Where possible the left foot shall be located approximately the same distance to the left of the centreplane of the 3 DH machine as the right foot is to the right. Manufacturer’s name and address: Two spirit levels orient the device in space.

A test force equal to H2 to the rear part of the seat corresponding to each seating position of the seat in the same vertical eve and in the same direction at the height H2 which shall be between 0. The general procedure indicated in paragraph 4. The actual torso angle corresponds theoretically to the design torso angle for tolerances see paragraph 3. Trade name or mark of the ecce Its first two digits at present 00 for the Regulation in its original form shall indicate the series of amendments incorporating the most recent major technical amendments made to the Regulation at the time of issue of the approval.

  ERLEND LOE NAIVE SUPER PDF

All fittings forming part of the back of the seat or ede thereto shall be such as to be unlikely to cause any bodily injury to a passenger during impact.

Manikin A manikin shall be installed behind each seating position of the seat to be tested eec follows: Shenzhen Bangnisen Auto Parts Co. If any movement of the feet has occurred during the rocking operation of the 3 DH machine, they must be fce as follows: The alignment of the sight buttons shall be maintained; Designated seating position: This device is described in appendix 1 to this annex; “‘H’ point” means the pivot centre of the torso and thigh of the 3 DH machine installed in the vehicle seat in accordance with paragraph 4 below.

The second digit is a capital letter which designates the location of the seating position in a row, as viewed in the direction of forward motion of the vehicle; the following letters shall be used: Each manikin required shall be installed on a seat in accordance with the following procedure: The direction of application of the force shall be situated in the vertical median plane of the seating position r0 it d80 be horizontal and from the rear towards the front of the seat.

The seat and the seat mountings are strong enough. List reference data for further seating positions under 3. If the 3 DH machine tends to slide rearward, use the following procedure. Reposition the 3 DH machine on the seat by one of the following methods: In this case, suitable controls means checking the dimensions of the ecce as well as the existence of procedures for the effective control of the quality of products.

Alternately, lift each foot off the floor the minimum necessary amount until no additional foot movement is obtained. If necessary, reposition the lower leg; If the 3 DH machine does not tend to slide rearward, use the following procedure. If the seat to be checked has never been sat upon, a 70 to 80 kg person or device shall sit on the seat twice for one minute to flex the cushion and back.

  AUCTEX REFERENCE PDF

ECE R80 Certified plastic bus seat, city bus seat, plastic seat for bus

For individual seats, the centreplane of the seat coincides with the centreplane of the occupant. If several seat types differing from one another in respect of the distance between the front and back ends of their feet can be mounted on the same anchorage, the test shall be carried out with the shortest footing. Other designated seating positions: The approval number indicates that the approval was granted in accordance with the requirements of Regulation No.

Not exactly what you want? China baby plastic seat China plastic seat shell China wheelchair plastic seat. If the seat is fitted with a table, it shall be in the stowed position. The direction of load application shall be maintained along a line passing by the above intersection to a point just above the thigh bar housing see figure 2 of appendix 1 to this annex.

Furthermore, the average deceleration shall be comprised between 6. Upon receiving the relevant communication that authority shall inform thereof the other Parties to the Agreement applying this Regulation by means of a communication form conforming to the model in annex 1 and or annex 2 to this Regulation.

The department may then either: The seat need not be an approved seat provided that it satisfies the requirements of paragraph 5.

Seat, Belt & Anchorage Test System | ECE-R14, ECE-R80 & FMVSS

Requirements for a seat type Another suitable test may be used provided that its equivalence with one of the prescribed tests is demonstrated. We have the ability to make the customized products according to the requirements.

As the case may be, the approval mark shall be placed on the seat or seats or on, or close to, the data plate affixed to the vehicle by the manufacturer.