HBM T10FS PDF

T10FS en. HBM. Safety instructions. Use in accordance with the regulations. Torque flanges T10FS are used exclusively for torque and rotation speed. The T10FS torque flange adds to the outstanding market reputation of the T10F torque flange, extending the range covered to greater accuracy, higher speeds. surement, additional reference pulse. Torque Flange. T10FS. T10FS. Rotor. Stator D T10FS en. HBM. 2. SUNSTAR传感与控制 -ic. com/.

Author: Vogar Milrajas
Country: Peru
Language: English (Spanish)
Genre: Environment
Published (Last): 5 August 2009
Pages: 281
PDF File Size: 9.2 Mb
ePub File Size: 1.38 Mb
ISBN: 751-3-58952-694-6
Downloads: 58410
Price: Free* [*Free Regsitration Required]
Uploader: Kagam

Electrical connection Possible faults and their elimination: Loosen and remove the upper antenna segment screw fitting.

Lot 641: HBM T10FS Torque Cell

HBM is offering you advanced torque calibration facilities for your torque sensors up to kNm. Calibration Calibration Calibration The T10F torque flange delivers an electrical calibration signal bbm can be switched at the amplifier end for measurement chains with HBM components.

T10F – Istruzioni per il montaggio. Turn the rotor by at least 2 min If both the control LEDs come on while you are turning the rotor, the speed measuring system is properly aligned and fully operational.

Use a piece of cloth or paper soaked in solvent. Finish installation of shaft train 4. Do not yet tighten the screws. Mounting The Rotor For safe torque transfer, the surfaces must be clean and free from grease. Sensors Torque Sensors T10F: The t10ffs channel data acquisition system measures and controls in real-time and is ideal for production processes and quality assurance.

  CEFADROXILA BULA PDF

When installed, the slotted disc should be exactly above this orientation hbk. Use compressed air up to 6 bar to clean the slotted disc. T10F – Prospetto dati.

HBM T10F MOUNTING INSTRUCTIONS Pdf Download.

Divergence of up to “2 mm is permissible in measuring mode total of static and dynamic shift. Align stator and finish installation 6. The precise value is specified on the type plate.

HBMshop See prices, availability and get an instant quote. Jbm refer to chapter 7. At a speed of 0 min the direction of rotation signal has the last measured value.

HBM T10FS Torque Cell

S the installation situation for example, covering, area free of metal parts S the length of the cable S the h10fs of the excitation voltage supply T10F A Comments to this Manuals Your Name. All product descriptions are for general information only. For when the calibration signal is unintentionally initiated with very short cables Normal position factory setting For cable lengths in excess of approx.

Cable sockets for speed and torque outputs Raw cables Wide range of couplings Further information can be found in the data sheet.

Installation Example With Couplings Mechanical installation 6. Important For correct operation, comply with the mounting dimensions see page The same applies to t10cs use of accessories.

Please click here to download CAD files. The difference between these versions lies in the electrical inputs and outputs on the stator, t1fs rotors bbm the same for all the versions of a measuring range. Page of 84 Go. No signal at the output, amplifier indicates overflow. Page 40 The stator should be fully grounded in the same way. Precision at its best: There is a mark orientation line in the sensor pickup for axial alignment orientation line. Guard against contamination from varnish fragments.

  CISTOADENOMA OVARICO PDF

S4 as per Tab.

Application Application The T10F torque flanges record static and dynamic torque on stationary or rotating shafts and determine the speed, specifying the direction of rotation. Don’t show me this message again. Enter text from picture: If the LED is on, the rotor and stator are properly aligned and there is no interference with the transmission of measurement signals.

The torque flanges can be used to measure static and dynamic torques. Aligning The Stator speed Measuring System There is a mark orientation line in the sensor pickup for axial alignment orientation line. Speed connector 2 Page 80 – Connector 2, double frequency, stat. T10F – Mounting instructions.

Page 34 – Aligning the stator speed measuring sys High accuracy and linearity with small hysteresis of up to 0. Page 10 Warranty In the case of complaints, a warranty can only be given if the torque flange is returned in the original packaging.